Your cart is currently empty!

In this blog, you’ll know what a NABL-accredited calibration checks, how to read the paperwork, and when to schedule the next one.
Key takeaways
Your logger reads 7.6 °C, so you sign the sheet and move on. But what if the real number was 8.4 °C? Here’s the thing: sensors drift, and drift never sends an alert. In the CDC’s opinion, temperature monitoring devices can drift over time, and devices that test outside ±0.5 °C (±1 °F) must be replaced. That’s a US vaccine rule, but the logic fits any cold chain. In this post, we’ll show you how NABL calibration services turn a reading into proof you can defend, what to look for on a calibration certificate, and how often to repeat the process.
Let’s break it down. Calibration means checking a device against a more accurate reference and writing down the difference. NABL is the National Accreditation Board for Testing and Calibration Laboratories, India’s accreditation body. It assesses calibration labs against ISO/IEC 17025, the international standard for lab competence.
So NABL calibration means the work was done by a lab that passed an outside check. In plain terms, ISO 17025 calibration services are the work, and NABL is the body that confirms the lab can do that work well.
Two more terms show up on every certificate. Traceability means your result links to a national or international standard through an unbroken chain of calibrations, each adding a little uncertainty. Measurement uncertainty is the plus-or-minus around a result. A reading without its uncertainty is only half an answer.
Say your product must stay between 2 °C and 8 °C, and your logger reads 0.8 °C low. It shows 7.6 °C while the product sits at 8.4 °C. Every record looks clean, yet you’ve had an excursion. (These numbers are made up to show the idea.)
What this really means is that a logger can be consistent and still wrong. Age, knocks, and rough handling all affect accuracy, and the CDC warns that household-store thermometers aren’t accurate enough to keep vaccines in range.
Calibration doesn’t make a sensor better by itself. It shows you the error so you can act on it. Here’s how the process usually goes:
That last step has a clear line in CDC guidance: if testing shows a device isn’t accurate within ±0.5 °C, replace it. This is where NABL calibration services earn their place in your quality system. You get an independent, documented answer instead of a guess, and that’s what protects your measurement accuracy over time.
A logo isn’t enough. Here’s a quick table to keep next to your audit binder. The first four rows follow the CDC’s list of what a certificate should show.
| What to check | Why it matters | Red flag |
|---|---|---|
| Model and serial number | Proves the certificate belongs to your device | Missing, or doesn’t match |
| Calibration date | Shows when the clock started | No date |
| Uncertainty | Tells you how far to trust the result (CDC recommends ±0.5 °C or less) | Not stated |
| Pass or in-tolerance result | Confirms the device met its limit | Only a “calibrated” stamp |
| Lab accreditation details | Lets you verify the lab and its scope | No details, or the scope doesn’t cover your range |
Next, check the lab itself. NABL accredits labs for a specific scope, so make sure the scope covers your range, whether that’s 2–8 °C or deep freeze. A lab can be accredited and still not cover what you need.
Loggers come first. Our Tempnote T32SU, for example, is listed at ±0.5 °C from -30 °C to +70 °C and ships with a hard-copy validation certificate. That’s a solid start. An independent temperature logger calibration by an accredited lab gives you a second, outside check as the device ages.
Storage and transport come next. Thermal mapping of a cold room or reefer vehicle only tells the truth if the sensors do. WHO’s model guidance covers calibration and verification of monitoring devices for both storage and transport.
Our NABL calibration services cover temperature, humidity, and pressure instruments, and we deliver them with NABL-accredited channel partners.
There’s no single answer. Here’s what two US sources say for vaccine data loggers:
| Source | Suggested interval |
|---|---|
| Oregon Health Authority | Every 24 months, or as the manufacturer recommends |
| Immunize.org | Every 2 to 3 years, or as the manufacturer recommends |
Treat these as benchmarks, not rules for your plant. Your SOP, regulator, or customer contract comes first. Recalibrate sooner if a logger gets dropped or you doubt a reading. The CDC says to replace the device or send it for testing when accuracy is in question.
Pull the certificates for your three most important loggers. Check each one against the table above. Put every due date in a shared calendar with a reminder 30 days out. If a certificate is missing a serial number or an uncertainty value, that’s your first fix.
A number on the screen is only as good as the check that’s behind it. NABL calibration services provide you with a traceable, documented answer so that your numbers stand up in audit and, more importantly, in the cold room. Begin with your most critical devices. Read the certificates closely and set the next due date before putting them away.
Want a second pair of eyes? Talk to a Tempnote expert through our contact page, or browse our data loggers.
It’s calibration done by a lab that NABL has assessed against ISO/IEC 17025. You get a traceable, documented result.
Not by itself. It measures the error against a traceable reference, so you can correct, adjust, or replace the device.
ISO/IEC 17025 is the standard. NABL is the body that checks whether a lab meets it.
Your SOP, regulator, or manufacturer will know. The US vaccine programs often refer to 2 to 3 years, and Oregon refers to 24 months.
The model, serial number, calibration date, uncertainty, and a pass result at minimum, per the CDC. Add the lab accreditation details too.